Clarion CD Player DRX6575z User Manual

Owner’s manual  
Mode d’emploi  
Manual de instrucciones  
DRX6575z  
AM/FMCDPLAYER  
WITHCD/MDCHANGERCONTROL  
LECTEURCDAM/FMAVEC  
COMMANDEDECHANGEURCD/MD  
RADIODEAM/FMYREPRODUCTORDEDISCOS  
COMPACTOSCONCONTROLDECAMBIADOR  
DEDISCOSCOMPACTOS/MINIDISCOS  
Clarion Co., Ltd.  
PE-2189B  
280-7223-00  
All Rights Reserved. Copyright © 1998: Clarion Co., Ltd.  
Printed in China / Imprimé en Chine / Inpreso en China  
1998/11 (S·C)  
 
Handling Compact Discs  
6. REMOTE CONTROL  
2. PRECAUTIONS  
Use only compact discs bearing the  
mark.  
Receiver for remote control unit  
1. When the inside of the car is very cold and  
the player is used soon after switching on  
the heater moisture may form on the disc or  
the optical parts of the player and proper  
playback may not be possible. If moisture  
forms on the disc, wipe it off with a soft cloth.  
If moisture forms on the optical parts of the  
player, do not use the player for about one  
hour. The condensation will disappear natu-  
rally allowing normal operation.  
3. When the auto antenna cord is connected to  
the car auto antenna cord, when the unit is  
switched to the radio mode (or theTV mode),  
the antenna is extended automatically. If the  
car is in a narrow space, the antenna may  
strike something, so be careful.  
Do not play heart-shaped, octagonal, or other specially shaped compact discs.  
To remove a compact disc from its storage  
Handling  
case, press down on the center of the case  
and lift the disc out, holding it carefully by the  
edges.  
• Do not use commercially available CD protec-  
tion sheets or discs equipped with stabilizers,  
etc. These may damage the disc or cause  
breakdown of the internal mechanism.  
• New discs may have some roughness around  
the edges. If such discs are used, the player  
may not work or the sound may skip. Use a  
ball-point pen or the like to remove any rough-  
ness from the edge of the disc.  
4. This unit uses a precision mechanism. Even  
in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate  
the rotating parts.  
Operating range: 30° in all directions  
Ball-point pen  
Roughness  
2. Driving on extremely bumpy roads which  
cause severe vibration may cause the sound  
to skip.  
Storage  
Signal transmitter  
• Do not expose compact discs to direct sun-  
light or any heat source.  
• Do not expose compact discs to excess hu-  
midity or dust.  
• Do not expose compact discs to direct heat  
from heaters.  
Remote control unit  
This equipment has been tested and found to  
comply with the limits for a Class B digital de-  
vice, pursuant to Part 15 of the FCC Rules.  
CAUTION  
USE OF CONTROLS, ADJUSTMENTS, OR  
PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN, MAY RE-  
SULT IN HAZARDOUS RADIATION EXPO-  
SURE.  
These limits are designed to provide reason-  
able protection against harmful interference in  
a residential installation.  
• Never stick labels on the surface of the com-  
pact disc or mark the surface with a pencil or  
pen.  
• Never play a compact disc with any cellophane  
tape or other glue on it or with peeling off marks.  
If you try to play such a compact disc, you may  
not be able to get it back out of the CD player  
or it may damage the CD player.  
• Do not use compact discs that have large  
scratches, are misshapen, cracked, etc. Use  
of such discs may cause misoperation or dam-  
age.  
Cleaning  
To remove fingermarks and dust, use a soft  
cloth and wipe in a straight line from the cen-  
ter of the compact disc to the circumference.  
• Do not use any solvents, such as commercially  
available cleaners, anti-static spray or thinner  
to clean compact discs.  
This equipment generates, uses, and can radi-  
ate radio frequency energy and, if not installed  
and used in accordance with the instructions,  
may cause harmful interference to radio com-  
munications. However, there is no guarantee  
that interference will not occur in a particular  
installation.  
THE COMPACT DISC PLAYER and MINI DISC  
PLAYER SHOULD NOT BE ADJUSTED OR  
REPAIRED BY ANYONE EXCEPT PROPERLY  
QUALIFIED SERVICE PERSONNEL.  
CHANGES OR MODIFICATIONS NOT EX-  
PRESSLY APPROVED BY THE MANUFAC-  
TURER FOR COMPLIANCE COULD VOID  
THE USER’S AUTHORITYTO OPERATETHE  
EQUIPMENT.  
• After using special compact disc cleaner, let  
the compact disc dry off well before playing it.  
If this equipment does cause harmful interfer-  
ence to radio or television reception, which can  
be determined by turning the equipment off and  
on, the user is encouraged to consult the dealer  
or an experienced radio/TV technician for help.  
INFORMATION FOR USERS:.  
CHANGES OR MODIFICATIONS TO THIS  
PRODUCT NOT APPROVED BY THE MANU-  
FACTURER WILL VOID THE WARRANTY  
AND WILL VIOLATE FCC APPROVAL.  
Flip Down Panel  
Inserting the Batteries  
MODEL  
The DRX6575z uses a flip-down structure that makes possible large-size displays.  
12V  
GROUND  
1. Turn the remote control unit over, then slide  
the rear cover in the direction of the arrow.  
3. Do not use the FLIP DOWN PANEL as a tray  
CAUTION  
When opening and closing the FLIP DOWN  
PANEL, be careful not to catch your fingers.  
They could be injured.  
AM 530-1710kHz/FM 87.9-107.9 MHz  
to place objects on when it is open.  
AA (UM-3/1.5V)  
Batteries  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDI-  
TIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFER-  
ENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTER-  
FERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY  
CAUSE UNDESIRED OPERATION.  
2. Insert the AA (UM-3/1.5V) batteries that came  
with the remote control unit facing in the di-  
rections shown in the figure, then close the  
rear cover.  
4. When closing the FLIP DOWN PANEL, do not  
press OPEN button 1.  
5. Strong impacts to the operating or display  
section can cause damage or deformation.  
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR  
SUB-CHAPTER J APPLICABLE AT DATE OF MANUFACTURE.  
CLARION CO., LTD.  
50 KAMITODA, TODA-SHI, SAITAMA-KEN, JAPAN.  
1. Always use the DRX6575z with the FLIP  
DOWN PANEL closed.  
6. If the FLIP DOWN PANEL does not open fully,  
gently open it with your hand.  
Notes:  
MANUFACTURED:  
Rear cover  
Using batteries improperly can cause them to ex-  
plode. Take note of the following points:  
When replacing batteries, replace both batteries  
with new ones.  
2. Do not force operations or use this device  
abnormally when opening or closing the FLIP  
DOWN PANEL.  
286-  
Clarion Co.,Ltd.  
MADE IN  
SERIAL No.  
PE-  
Bottom View of Source Unit  
Rear side  
Do not short-circuit, disassemble or heat batteries.  
Do not dispose of batteries into fire or water.  
Dispose of spent batteries properly.  
Be sure to unfold and read the next page.  
Veuillez déplier et vous référer à la page suivante.  
Cerciórese de desplegar y de leer la página siguiente.  
8
DRX6 5 7 5 z  
DRX6 5 7 5 z  
3
DRX6 5 7 5 z  
4
 
3. CONTROLS / LES COMMANDES / CONTROLES  
4. NOMENCLATURE  
5. DCP  
Note:  
The control panel can be detached to prevent theft. When detaching the control panel, store it in the  
DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.  
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).  
Source unit / Appareil pilote / Unidad fuente  
We recommend taking the DCP with you when leaving the car.  
Names of Buttons  
Removing the DCP  
1. Hold down POWER button 3 for 1 second  
Attaching the DCP  
1. Insert the right side of the DCP into the source  
unit.  
1 OPEN button  
9 Preset buttons (1 to 6)  
Direct buttons (1 to 6) (7 to 12)  
! DISP (display) button  
" ISR (instant station recall) button  
# BND (band) button  
TOP button  
2 ENT (enter) button  
Play/pause button  
or longer to turn off the power.  
2. Insert the left side of the DCP into the source  
unit.  
3 POWER button  
2.  
FNC (function) button  
4 TITLE button  
ADJ (adjust) button  
$ A-M (audio mode) button  
LOUD (loudness) button  
% SEARCH button  
5 SCN (scan) button  
PS/AS (preset scan/auto store) button  
6 RPT (repeat) button  
7 RDM (random) button  
8 Z-EHCR (z-enhancer) button  
2. Deeply push in OPEN button 1 to unlock  
1.  
& Rotary knob  
the FLIP DOWN PANEL.  
With the FLIP DOWN PANEL opened / Ouverture du PANNEAU RABATTABLE /  
Apertura del PANEL ABATIBLE  
If the FLIP DOWN PANEL does not open fully,  
gently open it with your hand.  
( CD insertion slot  
) Eject button  
CAUTION  
• The DCP can easily be damaged by shocks.  
After removing it, be careful not to drop it  
or subject it to strong shocks.  
Display Items  
• If the FLIP DOWN PANEL is kept open, the  
DCP may drop due to vibration of the car.  
1 Single disc indication  
2 Disc in indication  
" Long title indication  
3. Pull the DCP toward you and remove it.  
# Operation status indication  
This results in damage to the DCP. So close  
the FLIP DOWN PANEL or remove the DCP  
to store into the case.  
The frequency, play time, clock, etc. are dis-  
played.  
3 LD (loudness) indication  
4 A-M (audio mode) indication  
5 Function mode indication  
DCP  
• The connector connecting the source unit  
and the DCP is an extremely important part.  
Be careful not to damage it by pressing on  
it with fingernails, screwdrivers, etc.  
$ RDM (random) indication  
% RPT (repeat) indication  
& SCN (scan) indication  
( BAND indication  
The names of modes being selected, etc. are  
displayed.  
Display / Afficheur / Visualizador  
Note:  
6 MANU (manual) indication  
7 ST (stereo) indication  
• If the DCP is dirty, wipe off the dirt with a soft, dry  
cloth only.  
) DISC TITLE indication  
~ TRACK indication  
8 Z-EHCR (z-enhancer) indication  
9 DISC indication  
4. Close the HOLD FLAP.  
! Preset channel indication (1 to 6)  
Disc number indication (1 to 12)  
The disc numbers corresponding to the discs  
in the CD or MD changer light.  
HOLD FLAP  
CAUTION  
Be sure to close the HOLD FLAP for safety  
when removing the DCP.  
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.  
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.  
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.  
5
DRX6 5 7 5 z  
6
DRX6 5 7 5 z  
DRX6 5 7 5 z  
7
 
Functions of Remote Control Unit Buttons  
CD changer  
MD changer  
Mode  
Radio  
CD  
TV  
Button  
, FUNC  
Turns power on and off. When pressed and held for 1 second: Turns power off.  
Switches among radio, CD, CD changer, MD changer and TV.  
- BAND  
Plays the first track. Moves the next disc  
Top play. in increasing order.  
Switches reception  
band.  
Switches reception  
band.  
DISC UP  
PROG  
TOP  
Increases and decreases volume (in all modes).  
. VOLUME  
/ SEARCH  
Moves preset  
channels up and  
down.  
Moves tracks up  
and down.  
Moves tracks up  
and down.  
Moves preset  
channels up and  
When pressed and When pressed and down.  
held for 1 second:  
Fast-forward/  
fast-backward.  
held for 1 second:  
Fast-forward/  
fast-backward.  
: PLAY/PAUSE  
No function.  
Switches between  
Switches between  
No function.  
playback and pause. playback and pause.  
Turns mute on and off.  
; MUTE  
< ISR  
Recalls ISR radio station in memory.  
Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio  
mode only).  
Switches among main display, sub display and clock display.  
= DISP  
Preset scan.  
Scan play.  
Scan play.  
Preset scan.  
> SCN  
When pressed and  
held for 2 seconds:  
Auto store.  
When pressed and When pressed and  
held for 2 seconds: held for 2 seconds:  
Disc scan play.  
PS/AS  
Auto store.  
No function.  
No function.  
Repeat play.  
Random play.  
Repeat play.  
No function.  
? RPT  
When pressed and  
held for 2 seconds:  
Disc repeat play.  
BLS  
Random play.  
When pressed and TV and VTR.  
held for 2 seconds:  
Switches between  
@ RDM  
DOLBY NR  
MONI  
Disc random play.  
* Some of the corresponding buttons on the source unit and remote control unit have different functions.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
7. OPERATIONS  
Note: Be sure to read this chapter referring to the front diagrams of  
chapter “3. CONTROLS” on page 5 (unfold).  
Basic Operations  
Radio mode CD mode CD changer mode  
MD changer mode TV mode Radio  
CAUTION  
mode...  
Be sure to lower the volume before switch-  
ing off the unit power or the ignition key.The  
unit remembers its last volume setting. If you  
switch the power off with the volume up, when  
you switch the power back on, the sudden  
loud volume may hurt your hearing and dam-  
age the unit.  
External equipment not connected with CeNET  
is not displayed.  
Adjusting the volume  
Turning the Rotary knob & clockwise increases  
the volume; turning it counterclockwise de-  
creases the volume.  
The clock is displayed when the ignition key  
is turned to the ACC (accessory) or IGN (igni-  
tion-on) position even when the unit power  
is off. In some cars, the clock may momen-  
tarily disappear when the ignition key is  
turned to the START position. The clock will  
reappear after the engine has started and the  
ignition key is released to the IGN (ignition-  
on) position.  
The volume level is from 0 (minimum) to 33 (maxi-  
mum).  
Switching the display  
Press DISP button ! to select the desired display.  
Each time you press DISP button !, the display  
switches in the following order:  
Main display  
Turning on/off the power  
Note:  
• Be careful about using this unit for a long time with-  
out running the engine. If you drain the car’s bat-  
tery too far, you may not be able to start the en-  
gine and this can reduce the service life of the  
battery.  
Sub (title) display  
Clock display  
Main display...  
1. Press POWER button 3.  
2. The illumination and display on the unit light  
up. The unit automatically remembers its last  
operation mode and will automatically switch  
to display that mode.  
3. Press and hold POWER button 3 for 1 sec-  
ond or longer to turn off the power for the unit.  
Note:  
• System check  
The first time this unit is turned on after the wire  
connections are completed, it must be checked  
what equipment is connected. When the power is  
turned on, “SYSTEM CHCK” appears in the dis-  
play, so press POWER button 3. The system  
check starts within the unit. When the system  
check is complete, the power is turned off, so press  
POWER button 3 again.  
Once selected, the preferred display becomes  
the display default. When a function adjustment  
such as volume is made, the screen will mo-  
mentarily switch to that function’s display, then  
revert back to the preferred display several  
seconds after the adjustment.  
Selecting a mode  
1. Press FNC button 3 to change the mode of  
operation.  
2. Each time you press FNC button 3, the mode  
of operation changes in the following order:  
10  
DRX6 5 7 5 z  
Basic Operations  
Adjusting the balance  
When you have entered a title in a CD, it ap-  
pears in the sub display. If you have not en-  
tered a title, “NO-TITLE” appears in the title  
display instead. For information on how to en-  
ter a title, refer to the subsection “Entering  
titles” in the “Other Handy Functions”.  
1. Press A-M button $ and select “BAL”.  
2. Turning the Rotary knob & clockwise empha-  
sizes the sound from the right speaker; turn-  
ing it counterclockwise emphasizes the sound  
from the left speaker.  
Setting the Z-enhancer  
This unit comes with 3 types of sound tone effects  
stored in memory. Select the one you prefer.  
The factory default setting is “0”. (Adjustment  
range: L13 to R13)  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
The factory default setting is “OFF”.  
Each time you press Z-EHCR button 8, the tone  
effect changes in the following order:  
Adjusting the fader  
1. Press A-M button $ and select “FAD”.  
Z-ENHANCER 1Z-ENHANCER 2Z-  
ENHANCER 3OFFZ-ENHANCER 1”...  
• Z-ENHANCER 1: bass emphasized  
2. Turning the Rotary knob & clockwise empha-  
sizes the sound from the front speakers; turn-  
ing it counterclockwise emphasizes the sound  
from the rear speakers.  
• Z-ENHANCER 2: treble emphasized  
• Z-ENHANCER 3: bass and treble emphasized  
• OFF  
: no sound effect  
The factory default setting is “0”. (Adjustment  
range: F12 to R12)  
Adjusting the tone  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
Press A-M button $ and select the item to adjust.  
Each time you press A-M button $, the item  
changes in the following order:  
When Z-enhancer 1, 2 or 3 is set  
Adjusting the Z-enhancer  
1. Press Z-EHCR button 8 and select the Z-  
Z-EHCRBALFADFunction  
mode...  
enhancer mode (1 to 3) to adjust.  
2. Press A-M button $ and select “Z-EHCR”.  
Adjusting the bass  
1. Press A-M button $ and select “BASS”.  
3. Turning the Rotary knob & clockwise adjusts  
in the + direction; turning it counterclockwise  
adjusts in the – direction.  
2. Turning the Rotary knob & clockwise empha-  
sizes the bass; turning it counterclockwise  
attenuates the bass.  
When Z-enhancer 1 is selected, you can adjust  
the bass in the range of ±2.  
The factory default setting is “0”. (Adjustment  
range: –6 to +6)  
When Z-enhancer 2 is selected, you can adjust  
the treble in the range of ±2.  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
When Z-enhancer 3 is selected, you can adjust  
the bass and treble in the range of ±2.  
4. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
Adjusting the treble  
1. Press A-M button $ and select “TREB”.  
2. Turning the Rotary knob & clockwise empha-  
sizes the treble; turning it counterclockwise  
attenuates the treble.  
The factory default setting is “0”. (Adjustment  
range: –6 to +6)  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
Basic Operations  
Radio Operations  
Turning on/off the loudness  
FM reception  
For enhanced FM performance the  
tuner includes signal actuated stereo control, En-  
hanced Multi AGC, Impulse noise reduction curcuits  
and Multipath noise reduction circuits.  
®
The loudness effect emphasizes the bass and  
treble to create a natural sound tone. When you  
are listening to music at a low volume, it is rec-  
ommended to use the loudness effect.  
1. Press and hold LOUD button $ for 1 second  
or longer to turn on the loudness effect.When  
the loudness effect is turned on, “LD” lights in  
the display.  
Changing the reception area  
This unit is initially set to USA frequency intervals  
of 10kHz for AM and 200kHz for FM.When using it  
outside the USA, the frequency reception range  
can be switched to the intervals below.  
2. Press and hold LOUD button $ for 1 second  
or longer to turn off the loudness effect. “LD”  
goes off in the display.  
Setting the reception area  
1. Press BND button # and select the desired  
radio band (FM or AM).  
2. While pressing RDM button 7, each time you  
press and hold the number “1” of the Preset  
buttons 9 for 2 seconds or longer, the recep-  
tion area switches from inside the USA to out-  
side the USA or from outside the USA to in-  
side the USA.  
Any station preset memories are lost when the  
reception area is changed.  
Listening to the radio  
1. Press FNC button 3 and select the radio  
mode.  
2. Press BND button # and select the radio  
band. Each time the button is pressed, the  
radio reception band changes in the following  
order:  
FM1 FM2 FM3 AM FM1...  
3. Press the right or left side of SEARCH button  
% to tune in the desired station.  
Tuning  
There are 3 types of tuning mode available, seek  
tuning, manual tuning and preset tuning.  
Seek tuning  
1. Press BND button # and select the desired  
band (FM or AM).  
If “MANU” is lit in the display, press and hold  
BND button # for 1 second or longer. “MANU”  
in the display goes off and seek tuning is now  
available.  
2. Press the right or left side of SEARCH button  
% to automatically seek a station.  
When the right side of SEARCH button % is  
pressed, the station is sought in the direction  
of higher frequencies; if the left side of  
SEARCH button % is pressed, the station is  
sought in the direction of lower frequencies.  
12  
DRX6 5 7 5 z  
Radio Operations  
Manual tuning  
Auto store  
There are 2 ways available: Quick tuning and step  
tuning.  
When you are in the step tuning mode, the fre-  
quency changes one step at a time. In quick tun-  
ing mode, you can quickly tune the desired fre-  
quency.  
Auto store is a function for storing up to 6 sta-  
tions that are automatically tuned in sequentially.  
If 6 stations cannot be received, a previously  
stored station remains unoverwritten at the  
memory position.  
1. Press BND button # and select the desired  
1. Press BND button # and select the desired  
band (FM or AM).  
band (FM or AM).  
2. Press and hold AS button 5 for 2 seconds or  
longer. The stations with good reception are  
stored automatically to the preset buttons.  
If “MANU” is not lit in the display, press and  
hold BND button # for 1 second or longer.  
MANU” lights in the display and manual tun-  
ing is now available.  
Preset scan  
2. Tune into a station.  
Preset scan receives the stations stored in pre-  
set memory in order.This function is useful when  
searching a for desired station in memory.  
Quick tuning:  
Press and hold the right or left side of  
SEARCH button % for 1 second or longer to  
tune in a station.  
1. Press PS button 5.  
2. When a desired station is tuned in, press PS  
button 5 again to continue receiving that sta-  
tion.  
Step tuning:  
Press the right or left side of SEARCH button  
% to manually tune in a station.  
Note:  
• Be careful not to press and hold PS button 5 for  
2 seconds or longer, otherwise the auto store  
function engages and the unit starts storing  
stations.  
Recalling a preset station  
A total of 24 preset positions (6-FM1, 6-FM2, 6-  
FM3, 6-AM) exists to store individual radio sta-  
tions in memory. Pressing the corresponding pre-  
set button recalls the stored radio frequency au-  
tomatically.  
Instant station recall (ISR)  
Instant station recall is a special radio preset that  
instantly accesses a favorite radio station at a  
touch of a button.The ISR function even operates  
with the unit in other modes.  
1. Press BND button # and select the desired  
band (FM or AM).  
2. Press the corresponding Preset button 9 to  
recall the stored station.  
ISR memory  
Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store that station  
into preset memory.  
1. Select the station that you wish to store in ISR  
memory.  
2. Press and hold ISR button " for 2 seconds  
or longer.  
Manual memory  
1. Select the desired station with seek tuning,  
manual tuning or preset tuning.  
Recalling a station with ISR  
In any mode, press ISR button " to turn on the  
radio function and tune the selected radio sta-  
tion. “ISR” appears in the display. Press ISR but-  
ton " again to return to the previous mode.  
2. Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current  
station into preset memory.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
CD Operations  
Loading a CD  
1. Press OPEN button 1 to access the CD in-  
CAUTION  
Be careful not to catch your hand or fingers  
while closing the FLIP DOWN PANEL.  
sertion slot behind the FLIP DOWN PANEL.  
2. Insert a CD into the center of the insertion  
slot with the label side facing up.The CD plays  
automatically after loading.  
Notes:  
• If the FLIP DOWN PANEL does not open fully,  
gently open with your hand.  
• After taking out the CD, be sure to close the FLIP  
DOWN PANEL.  
If a CD (12 cm) is left in the ejected position for 15  
seconds, the CD is automatically reloaded (Auto  
reload).  
Notes:  
• Never insert foreign objects into the CD insertion slot.  
• If the CD is not inserted easily, there may be  
another CD in the mechanism or the unit may  
require service.  
3" CDs (8 cm) are not auto reloaded. Be sure to  
remove it when ejected.  
Notes:  
• Discs not bearing the  
mark and CD-ROMs  
cannot be played by this unit.  
If you force a CD into before auto reloading,  
this can damage the CD.  
Loading 3" (8 cm) compact discs  
• The radio mode is selected automatically 4 seconds  
after Eject button ) is pressed. If the auto antenna  
terminal for this unit is connected, the antenna is  
extended automatically. If you are in a location  
where the antenna may strike something, press  
FNC button 3 to switch the mode.  
No adapter is required to play a 3" CD.  
Insert the 3" CD into the center of the insertion slot.  
When a 3" CD is loaded, “SINGLE” lights in the  
display.  
3. Close the FLIP DOWN PANEL.  
• “DISC CHK” in the display shows you a CD is left  
in the unit. Be sure to press Eject button ) and  
remove it in this case.  
CAUTION  
Be careful not to catch your hand or fingers  
while closing the FLIP DOWN PANEL.  
Notes:  
Selecting a track  
Track-up  
• If the FLIP DOWN PANEL does not open fully,  
gently open with your hand.  
• After loading a CD, always close the FLIP DOWN  
PANEL.  
1. Press the right side of SEARCH button % to  
move ahead to the beginning of the next track.  
2. Each time you press the right side of SEARCH  
button %, the track advances ahead to the  
beginning of the next track.  
Listening to a CD already inserted  
Press FNC button 3 to select the CD mode. Play  
starts automatically. If no CD is loaded in the unit,  
NO DISC” appears in the display.  
Track-down  
1. Press the left side of SEARCH button % to  
move back to the beginning of the current track.  
Pausing play  
2. Press the left side of SEARCH button % twice  
1. Press Play/pause button 2 to pause play.  
PAUS” appears in the display.  
to move to the beginning of the previous track.  
Fast-forward/fast-backward  
Fast-forward  
2. To resume CD play, press Play/pause button  
2 again.  
Press and hold the right side of SEARCH button  
% for 1 second or longer.  
Ejecting a CD  
1. Press OPEN button 1 to open the FLIP  
Fast-backward  
DOWN PANEL.  
Press and hold the left side of SEARCH button  
% for 1 second or longer.  
2. Press Eject button ) to eject the CD. Take it  
out from the ejected position.  
DISC CHK” appears in the display when the  
CD is left in the ejected position.  
3. Close the FLIP DOWN PANEL.  
14  
DRX6 5 7 5 z  
CD Operations  
Other Handy Functions  
Top function  
Setting the clock  
The top function resets the CD player to the first  
track of the disc. Press TOP button # to play  
the first track (track No. 1) on the disc.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
2. Press the right or left side of SEARCH button  
Scan play  
% to select “CLOCK”.  
The scan play locates and plays the first 10 sec-  
onds of each track on a disc automatically. This  
function continues on the disc until it is canceled.  
3. Press ENT button 2.  
4. Press the right or left side of SEARCH button  
% to select the hour or the minute.  
The scan play is useful when you want to select a  
desired track.  
5. Turn the Rotary knob & clockwise or  
counterclockwise to set the correct time.  
1. Press SCN button 5 to start track scanning.  
SCN” lights in the display.  
The clock is displayed in 12-hour format.  
6. Press ENT button 2 to store the time into memory.  
2. To cancel the scan play, press SCN button 5  
again. “SCN” goes off from the display and  
the current track continues to play.  
7. Press ADJ button 4 to return to the previous mode.  
Note:  
You cannot set the clock when it is displayed with  
only the ignition on. If you drain or remove the car’s  
battery or take out this unit, the clock is reset. While  
setting the clock, if another button or operation is  
selected, the clock set mode is canceled.  
Repeat play  
The repeat play continuously plays the current  
track. This function continues automatically until  
it is canceled.  
1. Press RPT button 6. “RPT” lights in the dis-  
Entering titles  
play and the current track is repeated.  
Titles up to 10 characters long can be stored in  
memory and displayed for radio stations and  
CDs. The numbers of titles that can be entered  
for each mode are as follows.  
2. To cancel the repeat play, press RPT button  
6 again.RPT” goes off from the display and  
normal play resumes.  
Mode  
Number of titles  
30 titles  
Random play  
Radio mode  
CD mode  
TV mode  
The random play selects and plays individual tracks  
on a disc in no particular order. This function con-  
tinues automatically until it is canceled.  
50 titles  
15 titles  
1. Press RDM button 7. “RDM” lights in the dis-  
play, an individual track is selected randomly  
and play begins.  
CD changer mode  
CDC655z connected  
CDC655Tz connected  
CDC1255z connected  
Number of titles  
60 titles  
100 titles  
2. To cancel the random play, press RDM but-  
ton 7 again. “RDM” goes off from the display  
and normal play resumes.  
50 titles  
1. Press FNC button 3to select the mode you want  
to enter a title. (radio, CD, CD changer or TV)  
Titles cannot be entered for MDs with this unit.  
2. Select and play a CD or a CD in the CD changer  
or tune to an appropriate TV or radio station.  
3. Press DISP button ! and display the sub-  
title.  
4. Press TITLE button 4. “TITL” appears in the  
display and the cursor position flashes.  
5. Press the right or left side of SEARCH button  
% to move the cursor.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
Other Handy Functions  
6. Press DISP button ! to select a character.  
Each time you press DISP button !, the char-  
acter changes in the following order:  
Message display  
When the unit is powered on or off, a message is  
displayed. The user can turn this message dis-  
play on or off.  
Capital letters Numbers Capital letters...  
7. Turn the Rotary knob & to select the desired  
character. Turning the Rotary knob & clock-  
wise moves the cursor to the next character;  
turning it counterclockwise moves the cursor  
to the previous character.  
The factory default setting is “ON”.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
2. Press the right or left side of SEARCH button  
8. Repeat steps 5 to 7 to enter up to 10 charac-  
ters for the title.  
% to select “MESSAGE”.  
3. Press ENT button 2.  
9. Press and hold ENT button 2 for 2 seconds  
or longer to store the title into memory and  
cancel title input mode.  
4. Turn the Rotary knob & clockwise to set the  
message display to “ON”; turn it counterclock-  
wise to set the message display to “OFF”.  
5. Pressing ENT button 2 returns to the adjust-  
Clearing titles  
ment selection display.  
1. Play a CD or a CD in a CD changer or tune a  
radio station or TV station that you want to  
clear the title for.  
6. Press ADJ button 4 to return to the previous mode.  
2. Press DISP button ! and display the sub-  
title.  
3. Press TITLE button 4. “TITL” appears in the  
display and the display switches to the title  
input display.  
4. Press BND button #.  
5. Press and hold ENT button 2 for 2 seconds  
or longer to clear the title and cancel the title  
input mode.  
16  
DRX6 5 7 5 z  
8. OPERATIONS OF ACCESSORIES  
CD Changer Operations  
CD changer functions  
Selecting a CD  
When an optional CD changer is connected  
through the CeNET cable, this unit controls all  
the CD changer functions. This unit can control  
a total of 2 changers (MD and/or CD).  
Each of the Direct button 9 corresponds to a  
disc loaded into the magazine.  
Selecting a disc from 1 to 6  
Press the corresponding Direct button 9 (1 to  
Press FNC button 3 and select the CD changer  
mode to start play. If 2 CD changers are  
connected, press FNC button 3 to select the  
CD changer for play.  
6) to select the desired disc.  
Selecting a disc from 7 to 12 (only when a  
12 disc CD changer is used.)  
Press and hold the corresponding Direct button  
9 (7 to 12) for 1 second or longer to select the  
desired disc.  
If “NO MAG” appears in the display, insert the  
magazine into the CD changer. “LOADING” ap-  
pears in the display while the player loads (checks)  
the magazine.  
If “NO DISC” appears in the display, eject the  
magazine and insert discs into each slot. Then,  
reinsert the magazine back into the CD changer.  
If a CD is not loaded in a slot of the magazine,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Selecting a track  
Track-up  
CAUTION  
1. Press the right side of SEARCH button % to  
CD-ROM discs cannot be played in the CD  
changer.  
move ahead to the beginning of the next track.  
2. Each time you press the right side of SEARCH  
button %, the track advances ahead to the  
beginning of the next track.  
Pausing play  
1. Press Play/pause button 2 to pause play.  
PAUS” appears in the display.  
Track-down  
1. Press the left side of SEARCH button % to  
move back to the beginning of the current  
track.  
2. To resume play, press Play/pause button 2  
again.  
2. Press the left side of SEARCH button % twice  
Displaying CD titles  
This unit can display title data for CD-text CDs  
and user titles input with this unit.  
to move to the beginning of the previous track.  
Fast-forward/fast-backward  
1. Press DISP button ! to display the title.  
Fast-forward  
2. Each time you press and hold DISP button  
! for 1 second or longer, the title display  
changes in the following order:  
Press and hold the right side of SEARCH button  
% for 1 second or longer.  
Fast-backward  
User title (disc) CD-text title (disc) CD-  
text title (track) user title (disc)...  
Press and hold the left side of SEARCH button  
Note:  
% for 1 second or longer.  
• If the CD playing is not a CD-text CD or no user  
title has been input, “NO-TTL” appears in the dis-  
play.  
Scrolling a CD-text title  
When a CD-text title is longer than 11 characters,  
you can scroll the display as follows.  
1. Display the CD-text title (disc or track).  
2. Press TITLE button 4. The title scrolls.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
CD Changer Operations  
Top function  
Disc repeat play  
The top function plays from the first track (track  
No. 1) of the disc.  
After all the tracks on the current disc have been  
played, the disc repeat play automatically replays  
the current disc over from the first track. This  
function continues automatically until it is  
canceled.  
When playing a disc 1 to 6  
Press the Direct button 9 (1 to 6) with the same  
number as the CD playing.  
1. Press and hold RPT button 6 for 1 second  
or longer. “DISC” and “RPT” light in the dis-  
play and the disc repeat play starts.  
When playing a disc 7 to 12 (only when a  
12 disc CD changer is used.)  
Press and hold for 1 second or longer the Direct  
button 9 (7 to 12) with the same number as the  
CD playing.  
2. To cancel the disc repeat play, press and hold  
RPT button 6 again. “DISC” and “RPT” go  
off from the display and normal play resumes  
on the current track.  
If a CD is not loaded in a slot of the magazine,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Random play  
The random play selects and plays individual  
tracks on the disc in no particular order. This  
function continues automatically until it is  
canceled.  
Scan play  
The scan play locates and plays the first 10  
seconds of each track on a disc automatically.  
This function continues on the disc until it is  
canceled.  
1. Press RDM button 7. “RDM” lights in the dis-  
play and the random play begins.  
The scan play is useful when you want to select a  
desired track.  
2. To cancel the random play, press RDM but-  
ton 7 again. “RDM” goes off from the display  
and normal play resumes.  
1. Press SCN button 5 to start track scanning.  
SCN” lights in the display.  
2. To cancel the scan play, press SCN button 5  
again. “SCN” goes off from the display and  
the current track continues to play.  
Disc random play  
The disc random play selects and plays individual  
tracks or discs automatically in no particular  
order.This function continues automatically until  
it is canceled.  
Disc scan play  
The disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected CD changer. This function  
continues automatically until it is canceled.  
1. Press and hold RDM button 7 for 1 second  
or longer. “DISC” and “RDM” light in the dis-  
play and the disc random play starts.  
The disc scan play is useful when you want to  
select a desired CD.  
2. To cancel the disc random play, press and hold  
RDM button 7 again. “DISC” and “RDM” go  
off from the display and normal play resumes  
from the current track.  
1. Press and hold SCN button 5 for 1 second  
or longer. “DISC” and “SCN” light in the dis-  
play and the disc scan play starts.  
2. To cancel the disc scan play, press SCN but-  
ton 5 again. “DISC” and “SCN” go off from  
the display and the current track continues to  
play.  
Repeat play  
The repeat play continuously plays the current  
track. This function continues automatically until  
it is canceled.  
1. Press RPT button 6. “RPT” lights in the dis-  
play and the current track is repeated.  
2. To cancel the repeat play, press RPT button  
6 again. “RPT” goes off from the display and  
normal play resumes.  
18  
DRX6 5 7 5 z  
MD Changer Operations  
2. Each time you press the right side of SEARCH  
button %, the track advances ahead to the  
beginning of the next track.  
MD changer functions  
When an optional MD changer is connected  
through the CeNET cable, this unit controls all  
the MD changer functions. This unit can control  
a total of 2 changers (MD and/or CD).  
Track-down  
1. Press the left side of SEARCH button % to  
move back to the beginning of the current track.  
Press FNC button 3 and select the MD changer  
mode to start play. If 2 MD changers are  
connected, press FNC button 3 to select the  
MD changer for play.  
2. Press the left side of SEARCH button % twice  
to move to the beginning of the previous track.  
If “NO DISC” appears in the display, load MDs  
into the MD changer.  
Fast-forward/fast-backward  
Fast-forward  
Press and hold the right side of SEARCH button  
% for 1 second or longer.  
Pausing play  
1. Press Play/pause button 2 to pause play.  
PAUSE” appears in the display.  
Fast-backward  
Press and hold the left side of SEARCH button  
% for 1 second or longer.  
2. To resume play, press Play/pause button 2  
again.  
Top function  
Switching disc titles and track titles  
The top function plays from the first track (track  
No. 1) of the disc. Press the Direct button 9 (1  
to 6) with the same number as the MD playing.  
This unit can display disc titles and track titles  
already entered on MDs. Titles up to 128  
characters long can be displayed by scrolling the  
titles.  
If an MD is not loaded in a slot of the MD changer,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Titles cannot be entered for MDs with this unit.  
1. Press DISP button ! to display the title. The  
disc title or track title is displayed.  
Scan play  
The scan play locates and plays the first 10  
seconds of each track on a disc automatically.This  
function continues on the disc until it is canceled.  
2. Each time you press and hold DISP button  
! for 1 second or longer, the display toggles  
between the disc title and the track title.  
The scan play is useful when you want to select a  
desired track.  
Scrolling titles  
When a title is longer than 11 characters, you  
can scroll through it with the following operation.  
1. Press SCN button 5 to start track scanning.  
SCN” lights in the display.  
1. Display the MD title (disc or track).  
2. Press TITLE button 4.  
2. To cancel the scan play, press SCN button 5  
again. “SCN” goes off from the display and  
the current track continues to play.  
The display scrolls through the title.  
Selecting an MD  
Disc scan play  
Each of the Direct button 9 corresponds to an  
MD loaded into the MD changer. Press the cor-  
responding Direct button 9 (1 to 6) to select the  
desired disc.  
The disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected MD changer. This function  
continues automatically until it is canceled.  
If an MD is not loaded in a slot of the MD changer,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
The disc scan play is useful when you want to  
select a desired MD.  
1. Press and hold SCN button 5 for 1 second  
or longer. “DISC” and “SCN” light in the dis-  
play and the disc scan play starts.  
Selecting a track  
Track-up  
2. To cancel the disc scan play, press and hold  
SCN button 5 again. “DISC” and “SCN” go  
off from the display and the current track con-  
tinues to play.  
1. Press the right side of SEARCH button % to  
move ahead to the beginning of the next track.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
MD Changer Operations  
Repeat play  
TV Operations  
TV tuner functions  
The repeat play continuously plays the current  
track. This function continues automatically until  
it is canceled.  
When an optional TV tuner is connected through  
the CeNET cable, this unit controls all TV tuner  
functions. To watch TV requires a TV tuner and  
monitor.  
1. Press RPT button 6. “RPT” lights in the dis-  
play and the current track is repeated.  
Watching a TV  
1. Press FNC button 3 and select the TV mode.  
2. To cancel the repeat play, press RPT button  
6 again. “RPT” goes off from the display and  
normal play resumes.  
2. Press BND button # to select the desired TV  
band (TV1 or TV2). Each time the button is  
pressed, the input selection toggles between  
TV1 and TV2.  
Disc repeat play  
After all the tracks on the current disc have been  
played, the disc repeat play automatically replays  
the current disc over from the first track. This  
function continues automatically until it is  
canceled.  
3. Press the right or left side of SEARCH button  
% to tune in the desired TV station.  
Watching a video  
1. Press and hold RPT button 6 for 1 second  
or longer. “DISC” and “RPT” light in the dis-  
play and the disc repeat play starts.  
The TV tuner has a VTR input terminal to which  
1 external device can be connected. Connect a  
12V video cassette player (VCP) or video  
cassette recorder (VCR) to the TV tuner input  
terminal.  
2. To cancel the disc repeat play, press and hold  
RPT button 6 again. “DISC” and “RPT” go  
off from the display and normal play resumes  
on the current track.  
1. Press RDM button 7 to select VTR.  
2. To return to the TV broadcast, press RDM  
button 7.  
Random play  
The random play selects and plays individual  
tracks on the disc in no particular order. This  
function continues automatically until it is  
canceled.  
Tuning  
There are 3 types of tuning mode available, Seek  
tuning, manual tuning and preset tuning.  
1. Press RDM button 7. “RDM” lights in the dis-  
Seek tuning  
1. Press BND button # and select the desired  
play and the random play begins.  
2. To cancel the random play, press RDM but-  
ton 7 again. “RDM” goes off from the display  
and normal play resumes.  
TV band (TV1 or TV2).  
If “MANU” is lit in the display, press and hold  
BND button # for 1 second or longer. “MANU”  
in the display goes off and seek tuning is now  
available.  
Disc random play  
2. Press the right or left side of SEARCH button  
The disc random play selects and plays individual  
tracks or discs automatically in no particular  
order. This function continues automatically until  
it is canceled.  
% to automatically seek a station.  
Press the right side of SEARCH button % to  
automatically tune up the frequency band to  
the next available TV station; press the left  
side to automatically tune down.  
1. Press and hold RDM button 7 for 1 second  
or longer. “DISC” and “RDM” light in the dis-  
play and the disc random play starts.  
2. To cancel the disc random play, press and hold  
RDM button 7 again. “DISC” and “RDM” go  
off from the display and normal play resumes  
from the current track.  
20  
DRX6 5 7 5 z  
TV Operations  
Manual tuning  
Auto store  
There are 2 ways available: Quick tuning and step  
tuning.  
Auto store selects 6 TV stations automatically  
and stores each one into a preset memory.  
When you are in the step tuning mode, the  
frequency changes one step at a time. In quick  
tuning mode, you can quickly tune the desired  
frequency.  
If there are not 6 stations with good reception,  
stations previously stored in memory remain and  
only the strong stations are stored into memory.  
1. Press BND button # and select the desired  
1. Press BND button # and select the desired  
TV band (TV1 or TV2).  
band (TV1 or TV2).  
2. Press and hold AS button 5 for 2 seconds or  
longer. The stations with good reception are  
automatically stored to the Preset buttons 9.  
If “MANU” is not lit in the display, press and  
hold BND button # for 1 second or longer.  
MANU” lights in the display and manual tun-  
ing is now available.  
Preset scan  
2. Tune into a station.  
Preset scan allows the user to view each preset  
position before it automatically advances to the  
next preset. This function is useful for searching  
for desired TV station in memory.  
Quick tuning:  
Press and hold the right or left side of  
SEARCH button % for 1 second or longer to  
tune in a station.  
1. Press PS button 5.  
Step tuning:  
2. When the desired station is found, press PS  
Press the right or left side of SEARCH button  
% to manually tune in a station.  
button 5 again to remain tuned to that station.  
Note:  
• Do not press and hold PS button 5 for 2 seconds  
or longer. Doing so will trigger the auto store  
function and start storing stations into memory.  
Recalling a preset station  
A total of 12 TV stations can be stored (6-TV1  
and 6-TV2).This allows you to select your favorite  
TV stations and store them in memory for later  
recall.  
Setting the TV diver  
You can change the reception setting for the TV  
antenna connected to the TV tuner.  
1. Press BND button # and select the desired  
TV band (TV1 or TV2).  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
2. To recall a stored TV station, press the de-  
sired Preset button 9 to select that station.  
2. Press the right or left side of SEARCH button  
Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current sta-  
tion into the preset memory.  
% to select “TV DIVER”.  
3. Press ENT button 2.  
4. Turn the Rotary knob & clockwise to set to  
ON” or counterclockwise to set to “OFF”.  
Manual memory  
1. Select the desired station with seek tuning,  
manual tuning or preset tuning.  
ON:  
Sets reception emphasizing the visual.  
OFF:  
2. Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current  
station to that preset memory.  
Sets the diver setting to OFF.  
5. Press ENT button 2.  
6. Press ADJ button 4 to return to the previous  
mode.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
9. TROUBLESHOOTING  
Problem  
Cause  
Measure  
Power does not  
turn on.  
Fuse is blown.  
Replace with a fuse of the same amperage. If the  
fuse blows again, consult your store of purchase.  
(No sound is  
produced.)  
Incorrect wiring.  
Consult your store of purchase.  
No sound output  
when operating  
the unit with  
amplifiers or  
power antenna  
attached.  
Power antenna lead is  
shorted to ground or  
excessive current is required  
for remote-on the amplifiers  
or power antenna.  
1. Turn the unit off.  
2. Remove all wires attached to the power antenna  
lead. Check each wire for a possible short to  
ground using an ohm meter.  
3. Turn the unit back on.  
4. Reconnect each amplifier remote wire to the  
power antenna lead one by one. If the amplifiers  
turn off before all wires are attached, use an  
external relay to provide remote-on voltage  
(excessive current required).  
Nothing happens The microprocessor has  
when buttons are malfunctioned due to noise,  
Turn off the power, then press the OPEN button 1  
and remove the DCP.  
Press the reset button for about 2 seconds with a thin  
pressed.  
etc.  
rod.  
Reset button  
Display is not  
accurate.  
DCP or source unit  
connectors are dirty.  
Wipe the dirt off with a soft cloth moistened with  
cleaning alcohol.  
Compact disc  
Another compact disc is  
Eject the compact disc before loading the new one.  
cannot be loaded. already loaded.  
Sound skips or is Compact disc is dirty.  
noisy.  
Clean the compact disc with a soft cloth.  
Compact disc is heavily  
scratched or warped.  
Replace with a compact disc with no scratches.  
Sound is bad  
directly after  
power is turned  
on.  
Water droplets may form on  
the internal lens when the  
car is parked in a humid  
place.  
Let dry for about 1 hour with the power on.  
22  
DRX6 5 7 5 z  
10. ERROR DISPLAYS  
If an error occurs, one of the following displays is displayed.  
Take the measures described below to eliminate the problem.  
Cause  
Error Display  
ERROR 2  
Measure  
A CD is caught inside the CD deck and is  
not ejected.  
This is a failure of CD deck’s mechanism  
and consult your store of purchase.  
ERROR 3  
ERROR 6  
ERROR 2  
ERROR 3  
ERROR 6  
ERROR H  
A CD cannot be played due to scratches,  
etc.  
Replace with a non-scratched,  
non-warped disc.  
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.  
deck and does not play.  
A CD inside the CD changer is not loaded. This is a failure of CD changer’s mecha-  
nism and consult your store of purchase.  
A CD inside the CD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-warped  
disc.  
A CD inside the CD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
Displayed when the temperature in the  
MD changer is too high and playback has  
been stopped automatically.  
Lower the surrounding temperature and  
wait for a while to cool off MD changer.  
ERROR 2  
ERROR 3  
ERROR 6  
An MD inside the MD changer is not loaded. This is a failure of MD changer’s mecha-  
nism and consult your store of purchase.  
An MD inside the MD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-warped  
disc.  
An MD inside the MD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
Displayed when a non-recorded MD is  
loaded in the MD changer.  
Load a pre-recorded MD in the MD  
changer.  
If an error display other than the ones described above appears, press the reset button. If the problem  
persists, turn off the power and consult your store of purchase.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.DRX6 5 7 5 z  
11. SPECIFICATIONS  
FM Tuner  
Audio  
Frequency Range:  
Maximum Power Output:  
87.9 MHz to 107.9 MHz  
160 W (40 W × 4 ch) (EIAJ)  
Usable Sensitivity:  
11 dBf  
Continuous Average Power Output:  
14 W × 4, into 4 , 20 Hz to 20 kHz, 1%THD  
50dB Quieting Sensitivity:  
17 dBf  
Bass Control Action (30 Hz):  
±15 dB  
Alternate Channel Selectivity:  
75 dB  
Treble Control Action (10 kHz):  
±10 dB  
Stereo Separation (1 kHz):  
35 dB  
Line Output Level (CD 1 kHz):  
4 V  
Frequency Response (±3 dB):  
30 Hz to 15 kHz  
General  
Power Supply Voltage:  
14.4 V DC (10.8 to 15.6 V allowable),  
negative ground  
AM Tuner  
Frequency Range:  
530 kHz to 1710 kHz  
Current Consumption:  
Less than 15 A  
Usable Sensitivity:  
25 µV  
Speaker Impedance:  
4 (4 to 8 allowable)  
CD Player  
System:  
Weight / Source unit:  
3.75 lb. (1.7 kg)  
Compact disc digital audio system  
Weight / Remote control unit:  
1 oz. (30 g) (including battery)  
Usable Discs:  
Compact disc  
Dimensions / Source unit:  
7" (Width) × 2" (Height) × 6-1/8" (Depth)  
[178 (W) × 50 (H) × 155 (D) mm]  
Frequency Response (±1 dB):  
10 Hz to 20 kHz  
Dimensions / Remote control unit:  
1-3/4" (Width) × 4-5/16" (Height) × 1-1/8" (Depth)  
[44 (W) × 110 (H) × 27 (D) mm]  
Signal to Noise Ratio (1 kHz):  
100 dB  
Dynamic Range (1 kHz):  
95 dB  
Harmonic Distortion:  
0.01%  
Notes:  
Specifications comply with EIA Standards.  
Specifications and design are subject to change without notice for further improvement.  
24  
DRX6 5 7 5 z  

Compaq Server SC RMS User Manual
Continental Refrigerator Refrigerator SW48 10C FB User Manual
Craftsman Pressure Washer 58075213 User Manual
Craftsman Trimmer 31679617 User Manual
Crosley Refrigerator CS22AFXKB06 User Manual
Delfield Refrigerator UC4432N 12M User Manual
Dimplex Heat Pump SI 100ZS User Manual
D Link Network Router DWL G710 User Manual
Extron electronic Network Card RGB 460xi Series User Manual
Fundex Games Board Games 0734 00 11 User Manual